Boonruang, A., Thongchai, T., Jiang, Y., Demore, C.E.M., Neale, S. , Moldovan, A., Button, T.W. and Cochran, S. (2022) Progress towards wafer-scale fabrication based on gel casting technique for 1–3 randomised piezocomposite μUS linear array. Journal of the European Ceramic Society, 42(13), pp. 5565-5574. (doi: 10.1016/j.jeurceramsoc.2022.05.061)
![[img]](https://eprints.gla.ac.uk/style/images/fileicons/text.png) |
Text
277036.pdf - Published Version Available under License Creative Commons Attribution. 6MB |
Abstract
Microultrasound (μUS) linear arrays operating at frequencies over 25 MHz have applications in high resolution biomedical imaging. 1–3 connectively piezoceramic – polymer composite (“piezocomposite”) material is attractive for fabrication of these devices due to its high effective electromechanical coupling coefficient and low acoustic impedance for better acoustic matching between transducer and tissue. However, a major concern with this type of material comes from interference between the fundamental thickness-mode resonance and spurious modes, which is usually generated by wave propagation and reflection within the repetitive and symmetrical structure of classical piezocomposite. In general, a fine spatial scale is required of the material structure to suppress the spurious modes; however, the fabrication process is challenging using standard dice-and-fill methods at the fine scales required for high frequencies. A promising way to overcome this challenge is to manipulate the lateral geometry and spacing of the piezoceramic pillars with a random distribution. In this work, gel casting in association with a micromoulding technique has been developed for manufacturing 1–3 randomised piezocomposite active material for μUS linear arrays. 48 vol% solid loading of piezoceramic powder with 30 wt% Hydantoin resin content was employed to prepare a low viscosity aqueous suspension. Through varying powder size, it was found that the suspension with 1.22 µm powder had the highest viscosity, ~ 0.47 Pa.s, and a short gelation time, ~ 10 mins. However, all suspensions had viscosities less than 1 Pa.s at a shear rate of 100 s−1, indicating that they had good flowability. The green body samples showed mean flexural strength 49.7 ± 2.49 MPa. After piezocomposite fabrication with randomised pillars, surface planarisation was used to obtain reliable edge definition of photolithographically-defined electrodes. 20-element arrays with 50-μm element pitch were configured using a bilayer lift-off process. The 1–3 randomised piezocomposite demonstrated its capability to minimise the effects of spurious modes in the thickness mode frequency range, while the thickness resonances provided k33 = 0.67. Without a matching layer, the array produced a − 6 dB bandwidth of 38.4%- and − 20-dB pulse length of 0.26 μs. These results show that 1–3 randomised piezocomposite fabricated from gel-casting associated with a micromoulding technique is feasible for fabrication of μUS linear arrays and may offer a route to small wafer-scale production.
| Item Type: | Articles |
|---|---|
| Status: | Published |
| Refereed: | Yes |
| Glasgow Author(s) Enlighten ID: | BOONRUANG, ARJIN and Cochran, Professor Sandy and Moldovan, Dr Alexandru and Neale, Professor Steven |
| Authors: | Boonruang, A., Thongchai, T., Jiang, Y., Demore, C.E.M., Neale, S., Moldovan, A., Button, T.W., and Cochran, S. |
| College/School: | College of Science and Engineering > School of Engineering > Systems Power and Energy |
| Journal Name: | Journal of the European Ceramic Society |
| Publisher: | Elsevier |
| ISSN: | 0955-2219 |
| ISSN (Online): | 1873-619X |
| Published Online: | 26 May 2022 |
| Copyright Holders: | Copyright © 2022 The Authors |
| First Published: | First published in Journal of the European Ceramic Society 42(13): 5565-5574 |
| Publisher Policy: | Reproduced under a Creative Commons License |
University Staff: Request a correction | Enlighten Editors: Update this record
Altmetric
Altmetric